Dishwasher
IFB
Updated Jul 20, 2026
IFB Dishwasher E2 Error — Drainage Fault & How to Fix It
E2
IFB · DishwasherE2 on an IFB dishwasher means the machine cannot drain water properly. The drain is blocke…
Quick answer
E2 on an IFB dishwasher means the machine cannot drain water properly. The drain is blocked, the pump is faulty, or the hose is incorrectly positioned.
What E2 means
After each wash or rinse phase, the dishwasher pumps out the dirty water through the drain hose. E2 appears when the control board detects that water is still sitting in the tub after the drain pump has run for its maximum time. You will usually see standing water at the bottom of the tub when you open the door.
Common causes
The most frequent cause is food debris blocking the drain filter at the bottom of the tub. IFB dishwashers have a multi-layer filter system — if it is not cleaned regularly, food particles, grease, and debris accumulate and block drainage. The drain hose position also matters: if the hose outlet is too high or kinked, water cannot flow out.
Step-by-step fix
- Cancel the cycle and open the door. Scoop out any standing water with a cup or sponge.
- Remove and clean the drain filter. Open the filter assembly at the bottom of the tub (twist to unlock). Remove the coarse filter, fine filter, and mesh cup. Wash all parts under running water, scrubbing off grease and food particles.
- Check the drain hose. The hose should not be kinked, and the outlet should be at the correct height (refer to the installation guide — typically 40-80 cm from the floor).
- Check the sink connection. If the drain hose connects to a sink drain or garbage disposal, ensure that connection is not blocked.
- Run a rinse cycle. After cleaning the filter and checking the hose, run a short rinse cycle to see if E2 clears.
- If E2 persists: The drain pump may be faulty. Call IFB service.
Prevention: Scrape large food scraps off plates before loading. Clean the drain filter after every 3-4 wash cycles to prevent E2.
What does the E2 code mean?
E2 indicates the dishwasher cannot drain water from the tub within the expected time. The drain system is blocked or the pump is faulty.
Common causes
- Clogged drain filter (food debris, grease) — most common
- Kinked or blocked drain hose
- Drain hose outlet too high
- Blocked sink connection or garbage disposal
- Faulty drain pump motor
- Drain pump impeller jammed by debris (broken glass, toothpick)
Advertisement · In-content
How to fix the E2 error
Scoop out standing water
Open the door carefully and remove water with a cup or sponge.
Clean the drain filter
Remove the filter assembly from the tub floor. Wash all parts (coarse filter, fine filter, mesh cup) thoroughly.
Check the drain hose
Straighten kinks, verify outlet height (40-80 cm from floor).
Check sink connection
Ensure the hose-to-sink joint is not blocked.
Run a rinse cycle
Test if E2 clears after cleaning.
Call IFB service if persistent
Drain pump may need replacement.
Safety first: Standing water in the tub can contain sharp debris (broken glass). Wear gloves when scooping it out. Unplug the machine before accessing the drain pump.
Part you may need: Drain filter assembly / drain pump
IFB recommends cleaning the drain filter after every 3-4 cycles. A quick rinse prevents most E2 occurrences.
Frequently asked questions
How often should I clean the filter?
After every 3-4 loads, or immediately if you notice slow draining. It takes less than a minute.
Can I use the dishwasher with E2 showing?
No — the machine will not proceed with the cycle. Fix the drainage first.
E2 keeps coming back?
If the filter is clean and the hose is fine, the drain pump motor or impeller may be failing — call IFB service.
✎ Written by
REZAUL Karim (Riad)
REZAUL Karim (Riad) is the founder of ErrFixHub and a hands-on electronics and home-appliance repair specialist with over 15 years of experience diagnosing and fixing air conditioners, washing machines, refrigerators, inverters and other household appliances. He built ErrFixHub to turn cryptic error codes into clear, step-by-step fixes anyone can follow — cross-checking every code against manufacturer documentation and real repair-bench experience.
